Device
The following section explains how to pair AVVENTURA and Bluetooth® sensors to a smartphone, and how to configure various settings.
Important
• Changes are transferred when connecting the AVVENTURA to the smartphone (Cateye Cycling™).
* When connected to the smartphone, [Connect] will be displayed on the AVVENTURA, or will be displayed on the measurement screen.
* After the settings have been applied, switch [Connect] off.
• ANT+sensors are not displayed on the device screen even if pairing has been completed. Use the AVVENTURA to change the tire circumference for an ANT+ sensor.
Changing ANT+ sensor tire circumference
• When using third-party Bluetooth® sensors
Third party Bluetooth® sensor pairing information will not be transferred to the AVVENTURA. Pair using the method for pairing an ANT+ sensor.
Pairing an ANT+ sensor
Smartphone
1. Launch Cateye Cycling™, and from (Other), tap [Device].
Paired cyclocomputers and Bluetooth® sensors will be displayed.
• Pair to Device
Tap to pair a new device.
Set [Connect] to ON before tapping.
Configuring the AVVENTURA
Tap [AVVENTURA] to configure various settings.
Important
Changes are transferred when connecting the AVVENTURA to the smartphone (Cateye Cycling™). However, the following settings and information can only be viewed while the AVVENTURA is connected to the smartphone (Cateye Cycling™).
• Import from CC
• Remaining AVVENTURA battery
• Total Distance
• Firmware update
• Device Name:
Change the name of the AVVENTURA.• (Import from CC)
Displayed when trip data exists on the AVVENTURA connected to the smartphone (Cateye Cycling™).
Tap to display a list of trip data saved on the AVVENTURA. Trip data can be deleted or imported from this list.
Viewing trip data in the AVVENTURA• (Remaining Battery)
Indicates how much of the AVVENTURA’s battery power is remaining.• Delete
Tapping this will delete the displayed device.• Simple Navigation
This setting can be used to designate a goal to display in Simple Navigation.
Designating a goal• Countdown
Sets a distance or a time as a goal.• Target Altitude
This setting can be used to specify a target altitude.• Altitude Correction
Altitude correction is available if the GPS signal reception is poor and the altitude value is incorrect. If altitude correction is switched on and the AVVENTURA is connected to a smartphone before measurement starts, the altitude value measured by the app will be used for measurement. (The altitude value can be transferred before measurement or when paused, but [Connect] should be switched off after correction.)• Total Distance
Manually set total distance traveled.Important
Please note that any changes in the numerical value will change the total distance.
• Night Mode
Configure when to start and end backlight illumination, and how long illumination should last.
When Night Mode is enabled, the backlight will turn on for the specified amount of time.* When automatic display illumination is enabled, the start and end times of illumination will be adjusted automatically depending on the season.
• Display Customization
Select the measurement screens to add or delete in addition to the screen segments and functions (measurement data) to be displayed on each screen.
Changing the measurement screen• Lap Screen
Add or delete lap screens, and select screen segments and lap data to be displayed.
Changing the lap screen• Sounds
Turn the operation sounds, alert sounds, and notification sounds on or off.• Compass
Select whether to show or hide the compass on the measurement screen.• Screen Display
Select the language to be displayed on the measurement screen.• Data Auto Delete
When importing trip data saved in the AVVENTURA, users can choose whether to leave or delete the trip data after importing.• GLONASS
Select whether to use the GLONASS positioning system in addition to GPS for acquiring position information.
Using GLONASS will provide more accurate position information, but battery consumption will increase.• Recording Interval
Select the log interval for recording on the AVVENTURA.• Firmware
Verify the current firmware version and check the latest version available.
Updating the firmwareThis setting can also be used to update the firmware and to overwrite the firmware with that of a different language.
Bluetooth® sensor settings
Tap the name of the sensor to configure various settings.
Important
Changes are transferred when connecting the AVVENTURA to the smartphone (Cateye Cycling™).
• Device Name
Change the name of the sensor.* Paired sensors are displayed with “A” or “C” after the sensor name.
A: Sensor paired with Cateye Cycling™
C: Sensor paired with AVVENTURA• Delete
Tapping this will delete the displayed device.• Tire Circumference (only with a sensor capable of speed measurement)
Set the tire circumference for a sensor capable of speed measurement.
Scroll to find the tire size indicated on the sidewall of the tire. Tap and hold to choose the tire size.* Initial value: 2096 mm (700x23c)
* Set the tire circumference for each sensor capable of speed measurement.
Copyright © 2020 CATEYE Co., Ltd.